Were you looking for insight on A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a moderately difficult job. If the old bathtub is readily obtainable, the project can move quickly; if you need to open up a wall surface to remove the old bathtub and place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to vacate the old tub and set in the brand-new one. Ensure you have actually certified on your own for the job and are comfortable trying it. As opposed to working with a professional to take over a halfway-completed project, it is far better to take into consideration using one prior to you begin. Chances are you might need a professional plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your shower room if you have actually already bought a brand-new bathtub as well as don't need to change the arrangement of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the limited accessibility that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. Once the supply pipelines have been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before going on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the tap in position with the maker provided backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type ought to be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Making use of the two wooden boards under its feet, place the tub in the needed placement. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the supply of water and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Load the tub as well as also examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the tub needs to wait up until the bath tub has actually been utilized a minimum of once as this will settle it right into its last placement.
Getting ready for the Installation
Firstly, the sustaining frame supplied with the bath must be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a rigid seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, leading to complications with dampness as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes and cartridges, and are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched paper or soft rope. Remember to always fill up the tub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealer can crack fairly early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the market. It is a good idea to fit the tiles utilizing water-resistant or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that write-up about Tools You Need to Install a New Bathtub through someone on a different web page. Do you know about another individual who is enthusiastic about the niche? Why not share it. Many thanks for going through it.
Call, we deliver!